Ductwork Replacement Cost in Austin, TX

Ductwork Replacement Cost in Austin, TX

Ductwork replacement in Austin, TX generally costs between $2,000 and $7,000 per job, with the final figure depending on the size of your home, how easy the attic is to work in, and the insulation level of the new ducts. That range covers removing old runs and installing new ductwork, not duct cleaning, which is a separate service. If your system is losing air, has crushed or disconnected runs, or you are already replacing the air conditioner, it is worth getting a duct quote at the same time. This page covers what drives the price, when permits come into play, and how to vet an HVAC contractor before you sign.

Ductwork replacement cost

Most homeowners pay somewhere between $2,000 and $7,000 for ductwork replacement, quoted per job. A smaller single-story home with straightforward attic access tends to land at the low end, while a larger layout with tight runs, multiple zones, or a need for new insulation around the ducts pushes toward the high end. Those figures are typical national installed-cost ranges and are not adjusted for state or metro pricing, so treat them as a starting point rather than a bid.

It helps to see ductwork in context. Replacing a central AC at the same time runs $5,000 to $12,500, a furnace swap runs $3,000 to $7,500, and heat pump installation runs $5,000 to $15,000. A straightforward AC repair, by contrast, is $150 to $1,500. Because leaky or undersized ducts can make brand-new equipment underperform, many contractors price sealing or replacing the ducts alongside the equipment.

Duct cleaning is priced separately from replacement, so ask for that as its own line item if cleaning is part of what you want done. Get the scope in writing either way, because two quotes for ductwork replacement can cover very different amounts of material and labor.

Chart of typical ductwork replacement cost ranges
Typical installed cost ranges
ProjectTypical rangeMain cost drivers
Ductwork replacement$2,000–$7,000 per jobhome size, attic access, insulation level of ducts
Central AC replacement$5,000–$12,500 per jobtonnage and SEER2 rating, ductwork condition, refrigerant line changes
AC repair$150–$1,500 per jobpart (capacitor, fan motor, compressor), refrigerant, after-hours calls
Furnace replacement$3,000–$7,500 per jobgas vs electric, efficiency rating, venting changes
Heat pump installation$5,000–$15,000 per jobducted vs ductless, capacity, cold-climate models

Typical installed-cost ranges, labor and materials included. Your price depends on your home and the contractor – get two or three written estimates. Ranges are periodically reviewed.

What affects the price

  • Home size and how many rooms the system has to serve.
  • Attic or crawlspace access, including how tight or obstructed the runs are.
  • Insulation level of the ducts and whether new insulation is part of the quote.
  • Layout complexity such as two-story runs, multiple zones, or long trunk lines.
  • Whether old ductwork has to be removed and disposed of.
  • Whether the work is bundled with AC replacement, a furnace, or a heat pump.

Ways to save

  • Get at least three written quotes for the same scope so you can compare line by line.
  • Bundle ductwork with AC replacement, furnace work, or heat pump installation to reduce overlapping labor.
  • Ask whether sealing or repairing part of the system would meet your goals before committing to full replacement.
  • Ask about non-emergency scheduling, since quotes pulled during a peak-demand breakdown tend to be higher.
  • Request a breakdown of materials, labor, and disposal so you can spot padded line items.
  • Confirm the quote states how many runs and what duct material you are actually getting.

Permits

Permits are usually required for AC or furnace replacement, heat pump installation, new ductwork, and gas furnace connections. They are usually not required for filter changes, routine maintenance, or thermostat replacement. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections. Ask who is filing the paperwork and who is responsible for the inspection before any work starts, so a failed inspection does not land on you.

Usually needs a permit

  • Ac or furnace replacement
  • Heat pump installation
  • New ductwork
  • Gas furnace connections

Usually doesn’t

  • Filter changes
  • Routine maintenance
  • Thermostat replacement

Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections.

Hiring checklist

  • Confirm the contractor is licensed for HVAC work in your area and ask to see proof.
  • Get a written scope that names the duct material and how many runs are included.
  • Ask who pulls the permit and when inspections are scheduled.
  • Check that removal and disposal of old ductwork is included in the price.
  • Request references from jobs similar in size and layout to your home.
  • Read the warranty terms for both labor and materials before you sign.

Frequently asked questions

How much does ductwork replacement cost in Austin, TX?

Typical installed cost runs from $2,000 to $7,000 per job. Your number depends on home size, how accessible the attic or crawlspace is, and the insulation level of the ducts. Those figures are national installed-cost ranges rather than Austin-specific pricing, so use them to sanity-check bids, then compare quotes for the exact scope you were given.

Is duct cleaning included in that price?

No. The $2,000 to $7,000 range covers ductwork replacement, meaning removing old runs and installing new ones. Duct cleaning is a separate service with its own quote. If you want both, ask for them as separate line items so you can see what each one actually costs and decide whether you need cleaning at all.

Do I need a permit for new ductwork in Austin?

Permits are usually required for new ductwork, and also for AC or furnace replacement, heat pump installation, and gas furnace connections. They are usually not required for filter changes, routine maintenance, or thermostat replacement. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections.

Should I replace ductwork at the same time as my AC?

It is often worth pricing together, because leaky or poorly sized ducts can keep new equipment from performing the way it should. Central AC replacement alone runs $5,000 to $12,500, so combining the jobs can reduce duplicated labor and access costs. Ask your HVAC contractor to quote the two scopes separately and as a bundle so you can compare.

Could a repair be enough instead of full replacement?

Sometimes. Sealing leaks, reconnecting a detached run, or replacing one damaged section can solve comfort and airflow problems at a fraction of replacement cost, and a simple AC repair runs $150 to $1,500. Ask the contractor to explain what they found, which sections are failing, and why a repair would or would not hold up.

How do I compare HVAC contractors in Austin?

Start with written quotes that describe the same scope, then compare license status, permit handling, materials, and warranty terms. HomeImproverz ranks contractors by Google rating weighted by review count, which gives you a sense of consistent feedback rather than a single glowing review. Always ask for references from jobs similar in size to yours.

Cost guides

Nearby cities

Explore more

Find hvac contractors near you

Browse local pros by city, compare ratings and hours, and request written estimates.

HVAC Contractors by city

Last updated October 12, 2026

leave your comment