If you are weighing a heat pump for your Austin home, the first question is usually what it will cost. Heat pump installation generally runs from $5,000 to $15,000 per job, depending on the size of the system, whether ductwork already exists, and whether you choose a standard or cold-climate model. That range covers equipment and labor, but every house is different and quotes vary with the details. Below you will find what drives the price, when a permit is typically needed, how related work like duct replacement fits in, and the questions to ask an HVAC contractor before you sign.
Heat pump installation in Austin generally falls between $5,000 and $15,000 per job. That is a wide range because a heat pump is not one product. A ducted system that ties into existing ductwork is a different project from a ductless setup with wall-mounted heads, and each indoor unit adds equipment and labor.
Capacity matters too. A system sized for a large house costs more than one sized for a small one, and the sizing should be calculated rather than guessed. Cold-climate models, built to keep heating output up when outdoor temperatures drop, sit toward the higher end of the range.
For comparison, central AC replacement typically runs $5,000 to $12,500, furnace replacement $3,000 to $7,500, and ductwork replacement $2,000 to $7,000. AC repair is usually $150 to $1,500. If your ductwork is leaky or undersized, folding that work into the heat pump project changes the total. These are typical national installed-cost ranges, so treat them as a starting point for quotes rather than a fixed price.

| Project | Typical range | Main cost drivers |
|---|---|---|
| Heat pump installation | $5,000–$15,000 per job | ducted vs ductless, capacity, cold-climate models |
| Central AC replacement | $5,000–$12,500 per job | tonnage and SEER2 rating, ductwork condition, refrigerant line changes |
| AC repair | $150–$1,500 per job | part (capacitor, fan motor, compressor), refrigerant, after-hours calls |
| Furnace replacement | $3,000–$7,500 per job | gas vs electric, efficiency rating, venting changes |
| Ductwork replacement | $2,000–$7,000 per job | home size, attic access, insulation level of ducts |
Typical installed-cost ranges, labor and materials included. Your price depends on your home and the contractor – get two or three written estimates. Ranges are periodically reviewed.
Most jurisdictions treat a heat pump installation as permitted work, alongside AC or furnace replacement, new ductwork, and gas furnace connections. Simple tasks such as filter changes, routine maintenance, and thermostat replacement usually do not require a permit. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule the inspections. Ask who is pulling it before work starts, and keep the final inspection sign-off with your home records.
Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections.
Typical installed costs for heat pump installation fall between $5,000 and $15,000 per job. The final number depends on the type of system, its capacity, and whether cold-climate equipment is specified. Ductwork condition, electrical work, and how accessible the attic or crawlspace is can also move the price. Treat any single figure you hear as an estimate until a contractor has looked at your home.
Central AC replacement typically runs $5,000 to $12,500, which overlaps with the $5,000 to $15,000 range for heat pump installation. A heat pump provides both heating and cooling, so the two are not exactly like for like. If you are also facing furnace replacement, which commonly runs $3,000 to $7,500, a heat pump can change the overall math for your home.
Heat pump installation usually requires a permit, as do AC or furnace replacement, new ductwork, and gas furnace connections. Filter changes, routine maintenance, and thermostat replacement generally do not. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule the inspections. Confirm the details with your local building department before work begins.
It depends on the condition of what you already have. Ductwork replacement typically runs $2,000 to $7,000 per job, so it is a meaningful addition to the project. Leaky or undersized ducts can hold back a new system, and doing the work at the same time avoids opening up the same spaces twice. Ask the contractor to inspect the ducts and show you what they find.
Start with a few local companies and compare itemized written quotes rather than a single lump sum. HomeImproverz lists HVAC contractors in Austin and ranks them using Google ratings weighted by review count, which can help you build a shortlist. From there, confirm licensing and insurance, ask who pulls the permit, and get equipment model numbers in writing. Be cautious of quotes that skip system sizing.
Browse local pros by city, compare ratings and hours, and request written estimates.
Last updated October 12, 2026
You must be logged in to post a comment.