What an Electrical Panel Upgrade Costs in Austin, TX

What an Electrical Panel Upgrade Costs in Austin, TX

Most homeowners only think about the electrical panel when something forces the issue: breakers keep tripping, an addition needs more power, or an electrician says the old panel cannot keep up. In Austin, TX, a typical panel upgrade runs about $1,500 to $4,500 per job, and the final number depends on your home and the contractor you hire. That range covers the panel work itself, while utility service changes, permits and inspections can shift it. This page walks through what drives the cost, when a permit is needed, and how to compare bids from licensed electricians.

Electrical panel upgrade cost

The installed cost of an electrical panel upgrade usually falls between $1,500 and $4,500 per job. Where your project lands in that range depends mostly on the amperage change, such as moving from a 100A to a 200A panel, whether the utility service needs to change, and permit and inspection costs. A same-size replacement is generally simpler than a service upgrade that touches the meter, the mast or the incoming lines.

Other electrical work is often quoted at the same time, and knowing those ranges helps you compare bids. Whole-house rewiring typically runs $6,000 to $20,000, driven by home size, wall access and whether the panel is replaced too. Level 2 EV charger installation generally costs $800 to $2,500, depending on distance from the panel, panel capacity and charger hardware. Whole-house generator installation usually runs $7,000 to $20,000, with generator size, transfer switch and gas line or concrete pad affecting the price.

These are typical national installed-cost ranges, not quotes for your home. When you ask about the cost electricians in Austin TX charge, expect the final figure to reflect your panel, your service and the inspections your city requires.

Chart of typical electrical panel upgrade cost ranges
Typical installed cost ranges
ProjectTypical rangeMain cost drivers
Electrical panel upgrade$1,500–$4,500 per jobamperage (100A to 200A), utility service changes, permit and inspection
EV charger installation (Level 2)$800–$2,500 per jobdistance from the panel, panel capacity, charger hardware
Whole-house generator installation$7,000–$20,000 per jobgenerator size, transfer switch, gas line and concrete pad
Whole-house rewiring$6,000–$20,000 per jobhome size, wall access, panel replacement

Typical installed-cost ranges, labor and materials included. Your price depends on your home and the contractor – get two or three written estimates. Ranges are periodically reviewed.

What affects the price

  • The amperage change, such as moving from a 100A to a 200A panel.
  • Whether the utility service has to change along with the panel.
  • Permit and inspection requirements that apply to your project.
  • Whether related work, such as rewiring or a new circuit, is bundled into the same visit.

Ways to save

  • Get more than one written bid so you can compare what each electrician includes.
  • Bundle related work, like an EV charger circuit or rewiring, into a single visit.
  • Ask whether a same-size panel replacement is possible instead of a full service change.
  • Confirm who pulls the permit and which inspections are included before you sign.
  • Plan the project ahead of time rather than waiting for an emergency call.

Permits

Permits are usually required for panel upgrades, new circuits, EV charger circuits, generator installation and rewiring. Simpler work, like replacing a light fixture or outlet on an existing circuit, usually does not need one. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections. Ask your electrician who is pulling the permit and when the inspection is expected, and confirm the sign-off before you make the final payment.

Usually needs a permit

  • Panel upgrades
  • New circuits
  • Ev charger circuits
  • Generator installation
  • Rewiring

Usually doesn’t

  • Replacing a light fixture or outlet on an existing circuit

Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections.

Hiring checklist

  • Ask for license and insurance details before any work begins.
  • Get a written scope that names the panel size, the permit and the inspections.
  • Confirm the electrician will pull the permit and schedule the inspection.
  • Ask what happens if the utility service or meter also needs to change.
  • Get the price in writing with a clear note on what could change it.
  • Request the inspection sign-off before paying the final invoice.

Frequently asked questions

How much does an electrical panel upgrade cost in Austin, TX?

Typical installed costs run from about $1,500 to $4,500 per job. The exact price depends on the amperage change, whether the utility service has to be modified, and the permit and inspection fees that apply. Get a written bid that spells out the panel size, the permit and what is included before you compare offers.

Do I need a permit for a panel upgrade?

Panel upgrades usually require a permit, and so do new circuits, EV charger circuits, generator installation and rewiring. Replacing a light fixture or outlet on an existing circuit usually does not. Permit rules are set by your city or county building department, and many require the licensed contractor to pull the permit and schedule inspections, so ask who is handling that.

What drives the price electricians in Austin TX charge for panel work?

The main drivers are the amperage change, such as going from a 100A to a 200A panel, whether the utility service needs to change, and permit and inspection costs. Related work you bundle into the same visit can add to the total, which is part of why two bids for the same house can differ.

What other electrical projects might I price at the same time?

Homeowners often get quotes for several jobs at once. Whole-house rewiring typically runs $6,000 to $20,000, Level 2 EV charger installation about $800 to $2,500, and whole-house generator installation about $7,000 to $20,000. Each range depends on the work involved, so ask for an itemized bid rather than one lump sum.

How should I choose an electrician for a panel upgrade?

Ask for license and insurance details, a written scope that names the panel size, and confirmation of who pulls the permit and schedules the inspection. Compare at least a couple of bids based on the same scope of work. Get the inspection sign-off before you make the final payment.

Cost guides

Nearby cities

Explore more

Find electricians near you

Browse local pros by city, compare ratings and hours, and request written estimates.

Electricians by city

Last updated October 12, 2026

leave your comment